Inset double-bowl sink with drains near divider
Free CAD block from the Kitchen sinks library (155 blocks), drawn 1:1.
About this block
Inset double-bowl sink with drains near divider, drawn in plan, front and side elevation, all three projected from its 3D model so they match to the millimeter. It measures 2' 9" wide, 18½" deep and 12" high (85 cm × 48 cm × 30 cm), and it is drawn 1:1, full size, so it drops into any drawing set up in meters or in inches without rescaling.
It also comes as a 3D model built from these drawings.
From the Kitchen sinks library: 155 blocks drawn to one standard, each one available on its own.
In practice
Where it goes
Drains pulled in toward the divider leave the outer corners of each bowl flat, a detail that matters on a plumbing layout because both drains meet one trap under the middle. Put this inset double bowl on a kitchen floor plan, a drainage plan and a countertop plan for a laminate or wood top where the inset rim is shown.
Clearances to leave
The 33 in (84 cm) rim goes in a 36 in (90 cm) base, with the two drains close enough together for a single trap, and the bowls are 19 in (48 cm) deep, leaving a faucet ledge on a 25 in (64 cm) countertop. Keep 24 in (61 cm) of counter at one end and 18 in (46 cm) at the other, and a 42 in (107 cm) aisle.
Pairs with
Tapered faucet spout with lever on round base reaches the bowl centers well; in section use Undermount double-bowl sink profile with faucet. Compare Equal double-bowl sink with central faucet hole, where the drains sit centrally in each bowl.
Common questions
What are the dimensions of this block?
It measures 2' 9" | 85 cm wide by 18½" | 48 cm deep. The drawing is 1:1, full size, so it inserts at the right size in metric and in imperial drawings.
Is there a 3D model of this block?
Yes. A 3D model built from this block's drawings, 2' 9" wide, 18½" deep and 12" high, is free to download in STEP, DXF 3D, OBJ, GLB, 3MF and STL.
File formats, AutoCAD versions and units are explained on the formats page; every file is free for personal and commercial work under the license.
Details
Collections
Drawing at scale3 views
Seen from above beside a standing person, both at the same scale.
3D model
Built at real size from the plan drawing, as pressed stainless sheet: the plate and every bowl with sloped walls, the strainer where the plan has its drain, the overflow on the back wall and the waste below; drainers, upstands and faucets where the drawing has them. Drag to orbit, underneath too; scroll or pinch to zoom.
Dimensions and sizes
Width 2' 9" | 85 cm, depth 18½" | 48 cm, footprint 4.3 ft², height 12" | 30 cm.
Explore at scale
How big is it?
Footprint 4.3 ft², about 0.2× the floor area of a twin bed.
On your sheet
At 1" = 1'-0" the drawing prints 2.77 in × 1.56 in on Letter.
In the room
Plan at real sizeAll 3 checks pass
Galley kitchen layout
Built around the inset double-bowl sink with drains near divider, the block you are viewing.
Checks
- Aisle in front of the sink4' 5"Minimum 3' 3", recommended 3' 6"
- Work aisle between countertops4' 1"Minimum 3' 6", recommended 4' 0"
- Door swing to the nearest fixture (door moved to fit)4"Minimum 2", recommended 4"
Design notes
- Work aisle 3' 6" for one cook, 4' 0" for two (42 and 48 in).
- Keep sink, cooktop and fridge within a few steps: each leg of the work triangle 3' 11" to 8' 10".
- Leave 15½" of landing countertop beside the cooktop and 23½" beside the sink.
The kit, 3 blocks